Flyin 100G 40通道 AWG

1.      产品概述/Product Overview

This document presents the generic specification for the 40-channel 100GHz AWG MUX/DEMUX component supplied for use in DWDM system.

This component is designed for use within the C -band release of DWDM system. To decrease the power dissipation of the devices in different environmental conditions, the AWG package is special designed with selection of reliable thermal plastic with low thermal conduction, and the AWG operating temperature is controlled by using foil resist heater or Peltier TEC with thermistor temperature sensor. Different input and output fibers, such as SM fibers, MM fibers and PM fiber can be selected to meet different applications. 
 

 

Flyin’s label is only for spec review and can be no label or customer label on the device on delivered samples and products
 

 

 

2.      极限条件/Absolute Maximum Ratings (unless otherwise specified)

参数/Parameters
 条件/Conditions
 规格/Specifications
 单位/Units
 
 
  
 较小/Min.
 较大/Max.
 
工作温度/Operating Temperature
 产品正常工作时/Operating
 -5
 65
 oC
 
工作湿度/Operating Humidity
 产品正常工作时/Operating
 5
 95
 %RH
 
存储温度/Storage Temperature
 产品不工作时/Non_Operating
 -40
 +85
 oC
 
存储湿度/Storage Humidity
 产品不工作时/Non_Operating
 5
 95
 %RH
 


3.      光性能/Optical Specification  (平**AWG/ Flattop Thermal AWG)

参数/Parameters
 条件/Condition
 规格/Specs
 单位/Units
 
Min
 Typ
 Max
 
通道数/Number of Channels
  
 40
  
 
通道间距/Number Channel Spacing
 100GHz
 100
 GHz
 
中心波长/Cha. Center Wavelength
 ITU频率/ITU frequency.
 C -band
 nm
 
通带频率/Clear Channel Passband
  
 ±0.1
 nm
 
波长精度/Wavelength Stability
 Maximum range of the wavelength error  of all channels and temperatures in average polarization.
 ±0.05
 nm
 
-1 dB 带宽/-1 dB Channel Bandwidth
 Clear channel bandwidth defined by passband shape. For each channel
 0.4
  
  
 nm
 
-3 dB 带宽/-3 dB Channel Bandwidth
 Clear channel bandwidth defined by passband shape. For each channel
 0.6
  
  
 nm
 
插损/Optical Insertion Loss at ITU grid
 Defined as the minimum transmission at ITU wavelength for all channels. For each channel, at all temperatures and polarizations.
  
 4.5
 6.0
 dB
 
相邻通道隔离度/Adjacent Channel Isolation
 Insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power, all polarizations, within the ITU band of the adjacent channels.
 25
  
  
 dB
 
非相邻通道隔离度/Non-Adjacent, Channel Isolation
 Insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power, all polarizations, within the ITU band of the nonadjacent channels.
 30
  
  
 dB
 
总隔离度/Total Channel Isolation
 Total cumulative insertion loss difference from the mean transmission at the ITU grid wavelength to the highest power, all polarizations, within the ITU band of all other channels, including adjacent channels.
 22
  
  
 dB
 
插损一致性/Insertion Loss Uniformity
 Maximum range of the insertion loss variation within ITU across all channels, polarizations and temperatures.
  
 1.0
 1.5
 dB
 
方向性Directivity(Mux Only)
 Ratio of reflected power out of any channel(other than channel n)to power in from the input channel n
 40
  
  
 dB
 
插损平坦度/Insertion Loss Ripple
 Any maxima and any minima of optical loss across ITU band, excluding boundary points, for each channel at each port
  
  
 0.5
 dB
 
回损/Optical Return loss
 Input & output ports
 40
  
  
 dB
 
PDL/Polarization Dependent Loss in Clear Channel Band
 Worst-case value measured in ITU band
  
 0.3
 0.5
 dB
 
偏振模式色散/Polarization Mode Dispersion
  
  
  
 0.5
 ps
 
较大承受光功率/Maximum Optical Power
  
  
  
 23
 dBm
 
功率监控范围/MUX/DEMUX input/ output

Monitoring range
  
 -35
  
 +23
 dBm
 
        

1.       IL Represents the worst case over a +/-0.1nm window around the ITU wavelength.

2.       PDL was measured on average polarization over a +/- 0.1nm window around the ITU wavelength.

 

 

 

 

4.      机械尺寸/Mechanical Schematic and Dimensions 

尺寸/Dimensions
 150 x 65 x 16 (mm)
 
安装孔/ Space between space between screws
 140×58 (mm)
 
光纤类型/Fiber Type
 公共端Common SMF-28e fiber with 900um loose tube，，通道端Channels G652D ribbons
 
光纤编排/Fiber Format
 4x 12带纤/4x 12-fiber ribbons
 
输入光纤长度/ Input fiber length
 500mm ± 50mm with 900um loose tube 
 
输出光纤长度Output fiber length
 Ribbon200mm± 20 mm and Fan out 300mm± 30mm with 900um loose tube
 
光纤标识/fiber Identification
 光纤末端贴数码贴标识/

Label with channel number to be placed midway between fiber end-points
 
连接器类型/Connector Options
 Common
 LC/UPC
 
Channels
 LC/UPC
 
带纤光纤标识/Fiber

 
 1
 蓝/Blue
 2
 橙/Orange
 3
 绿/Green
 4
 褐/Brown
 5
 灰/Grey
 6
 白/White
 
7
 红/Red
 8
 黑/Black
 9
 黄/Yellow
 10
 紫/Purple
 11
 粉/Pink
 12
 水/Aqua
 
 

Fan-out
 

Fan-out
 
*可以按客户要求使用其他结构/Also available in other configuration

 

AWG Module
 
 



LC/UPC
 
Fiber Coding 
LC/UPC
 

 

 

 

 

 

 
 
               

 

 

5.      电子规格/Electrical Specifications

Only for the thermal AWG module which has an internal temperature control circuit.

NO.
 Parameters
 Notes
 Specifications
 Units
 
Min
 Typ
 Max
 
2.23
 Set-Point temperature of

component
 Optimum operating temperature section for thermal AWG

The commands could only set current temperature and threshold in this range.
 65
  
 90
 °C
 
2.24
 Set-Point temperature stability
 Over entire operating temperature range for thermal AWG
  
  
 ±0.5
 °C
 
2.25
 Heater Drive Voltage
  
  
 +5
  
 V
 
2.26
 Heater Drive Current
  
  
  
 2.5
 A
 
2.27
 Heater Power Dissipation

(maximum, stable)
  
  
  
 12.5
 W
 
2.28
 Heater Power Dissipation

(stable state)
 25°C ambient temperature
  
  
 6
 W
 
2.29
 AWG Temperature Settling

Time
 AWG warm up time from a cold start(25°C ambient temperature) to set point for thermal AWG
  
  
 7
 min
 
2.30
 AWG Temperature Settling

Time
 AWG warm up time from a cold start(-5°C ambient temperature) to set point for thermal AWG
  
  
 15
 min
 

Temperature control IC build inside

 

6.      电接口/Electric interface

Connector type: 10 pin FRC box type (2.54mm pitch) male connector.

Pin definition is as below:


NO.
 pin#
 Signal Name
 Type
 Direction
 Descriptions
 
2.31
 1
 +5V
 Power
 ----
 supply for Heater circuit
 
2.32
 2
 +5V
 Power
 ----
 supply for Heater circuit
 
2.33
 3
 +5V
 Power
 ----
 supply for control circuit
 
2.34
 4
 Ready
 TTL
 Output
 ※         Set HIGH when the internal temperature is at a set-point temperature.

※         Set LOW when the internal temperature is not at a set-point temperature (higher than the Upper Temperature Threshold or lower than the Under Temperature Threshold).

※         This ** should be 3.3V TTL level.
 
2.35
 5
 Alarm
 TTL
 Output
 ※         Set HIGH when the internal temperature is higher than the set-point temperature.

※         Set LOW when the internal temperature is not higher than the set-point temperature.

Pin4 and pin5 could be used to check the temperature’s status.

※         This ** should be 3.3V TTL level.
 
2.36
 6
 Enable
 TTL
 Input
 ※         If set HIGH, the heater circuit is activated.

※         If set LOW, the heater circuit is disabled.

※         This ** should be 3.3V TTL level.
 
2.37
 7*
 TX
 TTL
 Output
 RS232 transmit **

This ** should be 3.3V TTL level.
 
2.38
 8
 GND
 Power
 ----
 Ground
 
2.39
 9*
 Rx
 TTL
 Input
 RS232 receive **

This ** should be 3.3V TTL level.
 
2.40
 10
 GND
 Power
 ----
 Ground
 

*: Information available for inquiry includes Chip Temperature, Module Status, P/N & SN.

 

7.      可靠性说明/Reliability Specifications

The planar DWDM components described within this datasheet are fully qualified according to Telcordia reliability assurance requirements for fiber optic and opto-electronic components (GR-1221-CORE/UNC, Generic Reliability Assurance Requirements for Fiber Optic Branching Components, and Telcordia TR-NWT-000468, Reliability Assurance Practices for Opto-electronic Devices). The reliability report is available for request.

 
 

 

8.      订购信息/Ordering Part Code Sequence

AWG
 X
 XX
 X
 XXX
 X
 X
 X
 XX
 
 
 Band
 Number of Channels
 Spacing
 1st Channel
 Filter Shape
 Package
 Fiber Length
 In/Out Connector
 
C=C-Band

L=L-Band

D=C+L-Band

X=Customize
 16=16-CH

32=32-CH

40=40-CH

48=48-CH

XX=Special
 1=100G

2=200G

5=50G

X=Special
 C60=C60

H59=H59

C59=C59

H58=H58

XXX=special
 G=Gaussian

B=Broad Gaussiar

F=Flat Top
 M=Module

R=Rack

X=Special
 1=0.5m

2=1m

3=1.5m

4=2m

5=2.5m

6=3m

S=Specify
 0=None

1=FC/APC

2=FC/PC

3=SC/APC

4=SC/PC

5=LC/APC

6=LC/PC

7=ST/UPC

S=Specify